wiki:tutorial
This is an old revision of the document!
VPCS is not Swissknife, it only has a few commands to help us to study Cisco switch/router, that's all.
I use the next case to test the functions of VPCS.
The topology:
20000 30000 T2000 30002 20002
PC1 ---- f0/0 -* ^ *- f0/0 - PC3
| | |
| ^ |
T2001<-< R1 --- f1/0:f0/0 -- R0 --- f0/1:f1/0 --- R2 >-> T2002
| 21000 21001 | 21002 21003 |
PC2 ---- f0/1 -* | *- f0/1 - PC4
20001 30001 *----*-----*------*-------* PC9 30003 20003
30004 30005 30006 30007 21004 20008
| | | | | |
20004 20005 20006 20007 41000 41008
PC5 PC6 PC7 PC8 | |
*-----*
|
R3 >-> T2003
Routers
R1: console 2001
f0/0 connect PC1
f0/1 connect PC2
f1/0 connect R0
R2: console 2002
f0/0 connect PC3
f0/1 connect PC4
f1/0 connect R0
R0: console 2000
f0/0 connect R1
f0/1 connect R2
f2/0 connect PC5
f2/1 connect PC6
f2/2 connect PC7
f2/3 connect PC8
f2/4 connect R3
R3: console 2003
f0/0 connect R0
f0/1 connect PC9
IP address
2001:11::1
dhcp 192.168.1.1 192.168.11.1
/ / \
PC1 ----- f0/0 -* *- f0/0 - PC3
| | /
| 172.16.1.2 172.16.2.2 | 192.168.11.2
| \ / | 2001:11::2
R1 -- f1/0:f0/0 -- R0 -- f0/1:f1/0 -- R2
| / | / | ip auto
ip auto | 172.16.1.1 | 172.16.2.1 | 192.168.12.2
/ | | | \
PC2 ----- f0/1 -* | *- f0/1 -------- PC4
/ f2/0 1 2 | 3 4 \
2001:2::1 eui-64 *----*-----*------*----* 2001:12::1 eui-64
192.168.2.1 | | | | | R3 PC9 192.168.12.1
| | | | | | |
| | | | *---------*
PC5 PC6 PC7 PC8 f0/0 f0/1
PC1 get IPv4 address via dhcp
PC2 get IPv6 address via stateless auto configuration (RA)
no IPv4 address
PC3 192.168.11.2, default gateway 192.168.11.1
2001:11::2/64, using RS to find the router
PC4 get IPv6 address via stateless auto configuration (RA)
192.168.12.2, default gateway 192.168.12.1
PC5-6 192.168.3.5-6
2001:3::5-9
PC7-9 192.168.4.7-9, vlan3(192.168.4.1)
2001:4::7-9
ipv4 CIDR=24, ipv6 CIDR=64
wiki/tutorial.1289738546.txt.gz · Last modified: 2010/11/14 12:42 by mirnshi